Sale!

Apple Magic Trackpad – Glass Replacement

$29.90$39.90

-25%

Add to Cart

Apple Magic Trackpad - Glass Replacement $29.90$39.90
Guaranteed Safe Checkout

What if the Magic Trackpad glass panel is accidentally broken?

Cx9Z40oWQAATGlL

Contacted Apple. They don’t repair them, but replace them. For the price of a new one?

No, you can fix your Magic Trackpad glass with us.

O1CN01t05VNj1JQ7Vip8LxK 755621022 scaled 2

  • Original size customization.
  • Broken Magic Trackpad glass can be replaced without dismantling the machine.
  • AG frosted material, no different from the original touch.
  • 99% of users experience this glass without the slightest decrease in touch sensitivity.

What’s in the Box

Magic Trackpad glass

3M Product Adhesives

实拍 副本 scaled 1

Installation Tutorial

Installation Video

Magic Trackpad glass works by conducting finger current through the glass and 3M adhesive under the glass to the capacitive sensor board to sense gestures. Theoretically any conductive material can be replaced (no glass can also sense touch gestures normally), so the normal function of the replacement depends on whether the replacement process is correct and whether there is damage to the capacitive sensor board.

主图模型 副本 scaled 1

Installation Steps Reference

1. Heating
Before removing the glass use a household hair dryer to evenly blow heat to separate the glass area for 40~80 seconds. Temperature to soften the 3M adhesive under the glass is appropriate (<80 ℃).

Disassembly techniques and points to note.
Black capacitor board for printed circuit boards, scratches deeper easy to damage the printed circuit, so the tip of the knife should be avoided when the initial entry under the glass tip downward force, slowly parallel push into the blade in the glass under the glue surface cut away from 3m glue as parallel as possible scratch, glue cooling small scoring knife is more difficult to enter the glass under the glue surface, separating the glue and glass adhesion efforts, so the temperature drops feel the blade push into / slide difficult and laborious when you need to blow hot glass diligently. So that the glue to maintain a soft state to remove the glass can significantly reduce the difficulty of glass disassembly, until the glass disassembly is complete.

2021 wonderful control panel components are not heat-resistant, such as the use of constant temperature heating table, please control the heating temperature of 80 ℃ or less, and the heating time should not be too long.

图1

2. Magic Trackpad Glass Removal
① Glue softened from the glass broken more serious corner to start disassembly (as shown in the arrow), familiar with the glass and confirm the location of the black capacitor plate structure, from the edge to the middle gradually remove the edge of the small pieces of glass, until the remaining larger pieces of glass.

Tips.
Note that the knife with a readily retractable force to avoid cutting fingers, parallel to the glass scratching blade, such as force imbalance, the direction of force to guide the glass do not favor the black capacitor plate to avoid cutting the induction circuit.

Super tiny broken glass residue falling on the ground easily stabbed feet or blown into the eye, removal should always clean up, pay attention to good protection.

Recommended from the glass broken more serious corner to start dismantling based on this place is less likely to error knife accidentally inserted into the black capacitive inductor plate below the damage to the printed circuit considerations, please be sure to pay attention to do not wrongly disassemble the capacitive inductor plate, the need to disassemble the 3m adhesive in the black capacitive inductor plate, dustproof adhesive pad and aluminum alloy frame on the glass.

图2

② Blowing hot glass to soften the glue, vertical wonderful control board, around the surrounding parallel slowly down the ring cut a circle (at this time people use a standing position more convenient force), for further replacement of thicker fruit knife to remove large pieces of glass to open the entry point, but also to avoid knife error inserted into the black capacitive induction plate below.

③Selection of glass removal order
According to the size of the broken pieces from smaller to larger pieces, from all around to the middle of the demolition, priority cleaning edge easier to separate part.

As shown in the figure, after the removal of fine glass, the ring around the separation of a circle of bottom glue and glass adhesion, and then a longer thick fruit knife to separate the A, B area.
C, D area of the larger pieces of glass not easily removed can be broken into smaller pieces at the sharp corners or slender weaknesses before further removal.

If there is no thicker knife can be based on this a → b → c → d order will be larger pieces of glass broken into smaller pieces before further disassembly can be. (If you need this operation, please adjust the direction of the panel to pay attention to eye protection)

图3

图4 副本

3. Removal Of Residual Glue
①Remove the residual glue before you must carefully remove the small glass residue, to prevent fingers from being stuck!
②Remove the residual glue can be wiped with large alcohol tablets, or use dry alcohol tablets or plastic cards (such as discarded shopping cards and bank cards) to scrape off the residual glue after the hair dryer is heated and softened.
Professional maintenance tools recommended to soften the residual glue after heating the use of electric glue removal machine to select the hard glue stick to remove. Gum cooling at room temperature is more difficult to remove, heated and softened after the roll is relatively easy to remove.

Be careful not to wipe the panel with alcohol tablets when removing it. Alcohol tablets are used when removing residual glue after the panel is completely removed.

图5黄色 副本

4. Touch Function Test And Magic Trackpad Glass Installation
① After removing the residual adhesive, wipe clean the black capacitive inductor board with alcohol cotton pad, and directly cover the glass to test whether the touch function is normal.
② 3M adhesive sticky area as shown in the figure, first of all, will be given a custom adhesive paste on the black capacitive inductor board and dustproof adhesive pad around, tearing attention to the need for no vacancies and bubbles, so that the normal conduction of current, glass frosted face up to the right two corners of the position and then slowly down to align the left two corners, sticky gently pressed to normal use.